The Contessa Corner — manual bilge pump

Re: manual bilge pump

null@example.com (RaceRock) — Sat, 21 Sep 2013 05:08:54 +0000

Thanks again for the information. All I need is a new diaphragm.

Re: manual bilge pump

null@example.com (te) — Thu, 19 Sep 2013 13:52:18 +0000

I replaced my manual bilge pump as posted above your post. I never did determine the exact model, but believe the replaced pump was the original Henderson pump. The Defender kit fit exactly and is still working today. Good luck, Tom

Re: manual bilge pump

null@example.com (RaceRock) — Wed, 18 Sep 2013 22:01:52 +0000

Hi, Was the original pump a Henderson MK III P7/L? Did the new pump fasteners match the holes for the old pump? I have to repair or replace my existing MK III. Thanks

Re: manual bilge pump

null@example.com (RaceRock) — Wed, 18 Sep 2013 22:00:15 +0000

Hi, Was the original pump a Henderson MK III P7/L? Did the new pump fasteners match the holes for the old pump? I have to repair or replace my existing MK III. Thanks

Re: manual bilge pump

null@example.com (te) — Thu, 07 Dec 2006 16:27:07 +0000

Re: manual bilge pump

null@example.com (donald_duck) — Sun, 19 Nov 2006 12:52:37 +0000

Re: manual bilge pump

null@example.com (eebygumcaptain) — Wed, 09 Aug 2006 22:55:57 +0000

What type of replacement pump are you thinking of getting or would recommend ?

I want to replace my manual pump (might be a Whale) which is located in the rear port locker and can only be operated with the cockpit open. Not looking for Cape Horn proof but mid Atlantic and capable of being operated from the cockpit without opening any lockers !

Cheers

Re: manual bilge pump

null@example.com (John Clark) — Wed, 09 Aug 2006 01:03:56 +0000

With the nylon diaphragm actuator broken, the diaphragm full of age cracks, and the pump needing conversion before I can rebuild with overpriced parts for another discontinued model -- the writing's on the topsides. Time for a new pump. The old one's not Cape Horn bound, unless found fit to pump rum.

Re: manual bilge pump

null@example.com (eebygumcaptain) — Tue, 08 Aug 2006 22:19:26 +0000

Re: manual bilge pump

null@example.com (seeadler) — Tue, 08 Aug 2006 19:54:01 +0000

Four years ago I needed rubber parts for my Henderson Mark 3 (or 4). I was told that the only option was to buy the kit to convert from a Mark 3 to a Mark 5. Parts for the Mark 5 are available. The kit has expensive and should only be considered after investigating the purchase of a new pump. Try Holland Marine in Toronto for parts and conversion kit.

Re: manual bilge pump

null@example.com (John Clark) — Tue, 08 Aug 2006 02:27:56 +0000

Like others I've seen, my Contessa has a Henderson P7/L Mk III pump, mounted on-center in the lazarette with the handle socket projecting through a slot in the back of the cockpit. My understanding after searching the web in vain for spare parts is that this model was also used in British lifeboats. Regrettably, there seems to be no rebuild kit any more. I also need to replace the flanged, threaded plastic shaft that passes through the diaphragm because part of the flange broke, not enough to make the pump unusable but enough to be scary. So it looks like I'll have to replace the whole pump. Any opinions about the best replacement? The original indeed looks every bit of a lifeboat pump and I don't care to use anything much lighter duty. I'd rather not have to fill and re-drill the back of the cockpit, either, but that's probably hoping for too much.

Re: manual bilge pump

null@example.com (bilgeret) — Sat, 15 Jul 2006 03:15:57 +0000

My pump went south today on the eve of a big trip.West had a rebuild kit for 22 dollars much to my surprise.This pump is red,Canadian made and called a "guzzler",forget the manafacturer but I think they must be in Windsor.It is comparable to the gulper or urchin by Whale.A bit light duty but it does move a surprising amount of water.

Re: manual bilge pump

null@example.com (bilgeret) — Thu, 29 Jun 2006 22:31:12 +0000

I tried the cheap fix a few years ago on another boat and it worked for a while but ultimately failed.The Whale/henderson diaphrams are formed in such a way that they can be flexed many thousands of times without stressing the seal or itself.The flat home made diaphram is stretched each time the pump is stroked so that eventually something has to give.I was a lot happier with the kit in the pump,my thinking being that when you "need" a pump,you really need it.

Re: manual bilge pump

null@example.com (Christopher) — Wed, 28 Jun 2006 02:52:23 +0000

Good day!

If your bilge pump is the same as mine then it is a Henderson Mark V (sometime it is written as Henderson MK V). It is a black beast mounted on the inside of the port cockpit locker, between the locker and the lazarette. To do the rebuild the easiest by far is to remove the pump.

I undertook the same project two years ago. You can still source the rebuild kits for these pumps although it appears that they are out of production. A caution: the rebuild kit is fabulously expensive -- comparable to a replacement pump. However, when I complained about the price at the marine store where I purchased the kit, I was told that the Henderson is a much better pump than anything else.

The same pump, in white, is used as the prime mover for the Lavac heads btw.

Having rebuilt mine, it has worked like a charm. It is well worth the expense and effort in my opinion.

Good luck!

Re: manual bilge pump

null@example.com (eebygumcaptain) — Wed, 21 Jun 2006 20:36:54 +0000

Hi, this happened to me as well.

The local marine shop was quoting me a fortune for a new replacement kit and I wasn't sure it was the right one. Thinking I might be able to buy a replacement peice of rubber from the local DIY superstore I decided to pop in on my way home......driving there I'm racking my brains as where I might find a suitable product....flexible, strong rubber, 3-4 mm thick, water resistent and able to be cut to shape and cheap....changing gear as I came into the carpark I had a Eureka moment.....my rubber car mats; cost 2 dollars for two, makes enough for sevral diaphragms and in/out flaps.

Works a treat and show no signs of failing despit quite a lot of pumping before I got my cockpit floor sorted out.

Cheers
Andrew